Influence of the multiday and continuous hot press on the physical, mechanical and formaldehyde emission properties of the particleboard

Authors

  • Osman Camlibel

Keywords:

Continuous hot press, formaldehyde content, multiday hot press, particleboard, physical-mechanical properties

Abstract

In this study, Its the influence of according to press, particleboards produced in two different press types which were multiday and continuous hot press, the thickness, density, bending strength, modulus of elasticity, internal bond, surface soundness, withdrawal of screw resistance, moisture, thickness swelling, water absorption, formaldehyde emission content were researched. 18 mm x 2100 mm x 2800 mm size particleboards were manufactured on the production line which was using urea-formaldehyde (F:U;1,07 moles), and 30 % pine, 40 % oak, 20 % beech and 10 % poplar waste mixture of the wood materials. According to results of the tests performed after the multiday and continuous hot press production of the boards; thickness (0,63 %), bending strength (1,27 %), moisture content (0,47 %), thickness swelling (37 %), and water absorption (39,9 %), modulus of elasticity (11,35 %), internal bond (7,22 %) were increased according to multiday hot press while density (2,7 %), surface soundness (18,81 %), withdrawal of screw resistance (14 %) and formaldehyde (57,12 %) decreased. Formaldehyde content,surface soundness, withdrawal of screw resistance are the most prominent properties influenced by continuous hot press.

Downloads

Download data is not yet available.

References

Ayla, C. 1999. Sürekli Laminat Üretimi. Laminart Magazine 1(1): 26-29. http://www.laminartdergisi.com./sayı1

Arruda, L.M.; Del Menezzı, C.H.S.; Teıxeıra, D.E.; De Araujo, P.C. 2011. Lignocellulosic composites from Brazilian giant bamboo (Guadua magna) Part 1: Properties of resin bonded particleboards. Maderas-Cienc Tecnol 13(1): 49-58. http://dx.doi.org/10.4067/S0718-221X2011000100005

Barragan-Lucas, A.D.; Llerena-Miranda, C.; Quijano-Avilés, M.; Chóez-Guaranda, I.A.; Maldonado-Guerrero, L.C.; Manzano-Santana, P.I. 2019. Effect of resin content and pressing temperature on banana pseudostem particle boards properties using full factorial design. An Acad Bras Cienc 91: e20180302. https://doi.org/10.1590/0001-3765201920180302

Candan, Z.; Akbulut, T.; Wang, S.; Zhang, X.; Faruk Sisci, A. 2012. Layer thickness swell characteristics of medium density fibreboard (MDF) panels affected by some production parameters. Wood Res Slovakia 57(3): 441-452. http://www.woodresearch.sk/wr/201203/10.pdf

Ciobanu, V.D.; Zeleniuc, O.; Dumitrascu, A.; Lepadatescu, B.; Iancu, B. 2014. The influence of speed and press factor on oriented strand board performance in continuous press. BioResources 9(4): 6805-6816. https://bioresources.cnr.ncsu.edu/resources/the-influence-of-speed-and-press-factor-on-oriented-strand-board-performance-in-continuous-press/

Camlibel, O. 2020. Sıcak pres parametrelerinin yonga levhanın fiziksel özellikleri ve formaldehit emisyonuna etkisi. Artvin Çoruh Univ Orman Fak Ders 21(2): 276–283. https://doi.org/10.17474/artvinofd.740136

Camlibel, O.; Aydın, M. 2022. The effects of continuous press speed and conditioning time on the particleboard properties at industrial scale. BioResources 17(1): 159-176. https://bioresources.cnr.ncsu.edu/resources/the-effects-of-continuous-press-speed-and-conditioning-time-on-the-particleboard-properties-at-industrial-scale/

Camlibel, O. 2021. The Effect of Multi-Layer Press Parameters on Mechanical Properties in Particleboard Production. TURKJANS 8(3): 800–807. https://doi.org/10.30910/turkjans.870258

Camlibel, O.; Ayata, U. 2021. The Effect of Mole Ratio on Some Physical, Mechanical and Formaldehyde Emissions in High-Density Fibreboards (HDF). Night Library Publishing House, 335pp.

Godbille, F.D. 2002. A simualtion model for the hot pressing of particleboard. The University of New Brunswick, Canada.

Güler, C.; Sancar, S. 2016. Yonga levha Fabrikasının Çalışma Prensibi ve Farklı Presleme Tekniğinin Levha Kalitesi Üzerine Etkisi. Ormancılık Dergisi 12(1): 1-10. (In Turkish). http://ordergi.duzce.edu.tr/Dokumanlar/arsiv/2016_1_Tam.pdf

Ciobanu, V.D.; Zeleniuc, O.; Dumitrascu, A.E.; Lepadatescu, B.; Iancu,B. 2014. The influence of speed and press factor on oriented strand board performance in continuous press. BioResources 9(4): 6805–6816. https://bioresources.cnr.ncsu.edu/wp-content/uploads/2016/06/BioRes_09_4_6805_Ciobanu_ZSLI_Oriented_Strand_Bd_Perform_Speed_Continuous_Press_6110.pdf

Evessen, H.S. 1984. Continuous pressing processes in particleboard production-The Küsters press-process. Holz Roh Werkstoff 42(2): 63-66.

Ferrandez-Villena, M.; Ferrandez-Garcia, C.E.; Garcia-Ortuño, T.; Ferrandez-Garcia, A.; Ferrandez-Garcia, M.T. 2020. The influence of processing and particle size on binderless particleboards made from Arundo donax L. Rhizome. Polymers 12(3): 696. https://doi.org/10.3390/polym12030696

Funk, M.; Wimmer, R.; Adamopoulos, S. 2017. Diatomaceous earth as an inorganic additive to reduce formaldehyde emissions from particleboards. Wood Mat Sci Eng 12(2): 92-97. https://doi.org/10.1080/17480272.2015.1040066

Hong, M.K.; Lubis, M.A.R.; Park, B.D. 2017. Effect of panel density and resin content on properties of medium-density fiberboard. J Korean Wood Sci Technol 45(2017): 444–455. https://doi.org/10.5658/WOOD.2017.45.4.444

Iswanto, A.; Febrianto, F.; Hadi, Y.; Ruhendi,S. Hermawan, D. 2013. The Effect of Pressing Temperature and Time on the Quality of Particle Board Made from Jatropha Fruit Hulls Treated in Acidic Condition. Makara J Technol 17(3): 145-151. https://doi.org/10.7454/mst.v17i3.2930

Istek, A.; Özlüsoylu, İ.; Onat, M.S.; Özlüsoylu, Ş. 2018. Formaldehyde Emission Problems and Solution Recommendations on Wood-Based Boards Formaldehyde Emission Problems and Solution Recommendations on Wood-Based Boards: A review. J Bartin Fac For 20(2): 382-387. https://dergipark.org.tr/en/pub/barofd/issue/36468/425409

Kord, B.; Roohani, M.; Kord, B. 2015. Characterizatıon and utilizatıon of reed stem as a lignocellulosic resource for particleboard productıon. Maderas-Cienc Tecnol 17(3): 517- 524. http://dx.doi.org/10.4067/S0718-221X2015005000046.

Lv, Y.; Liu, Y.; Jing, W.; Woźniak, M.; Damaševičius, R.; Scherer, R.; Wei, W. 2020. Quality control of the continuous hot-pressing process of medium density fiberboard using fuzzy failure mode and effects analysis. Appl Sci 10(13): 4627. https://doi.org/10.3390/app10134627

Nemli, G. 2002. Factors affecting the production of E1 type particleboard. Turk J Agric For 26(1): 31–36. https://dergipark.org.tr/en/download/article-file/120105

Nemli, G.; Kalaycıoğlu, H.; Akbulut, T. 2004. Influence of press type on the technological properties of particleboard. Artvin Çoruh Univ Orman Fak Derg 5(1): 89-95. http://ofd.artvin.edu.tr/tr/pub/issue/2253/29691.

Nitu, I.P.; Islam, Md.; Ashaduzzaman, Md.; Amin, Md.K.; Shams, Md.I. 2020. Optimization of processing parameters for the manufacturing of jute stick binderless particleboard. J Wood Sci 66: 65. https://doi.org/10.1186/s10086-020-01913-z

Maraghi, M.M.R.; Tabei, A.; Madanipoor, M. 2018. Effect of board density, resin percentage and pressing temperature on particleboard properties made from mixing of poplar wood slab, citrus branches and twigs of Beech. Wood Res Slovakia 63(4): 669–682. http://www.woodresearch.sk/wr/201804/12.pdf.

Saad, A.; Kasim, A.; Gunawarman, S. 2019. Optimization of Composition, Temperature and Time on Production of Particle Board Made from Pine Bark and EFB, in: IOP Conference Series. Earth Environ Sci 327: 012015. https://iopscience.iop.org/article/10.1088/1755-1315/327/1/012015/meta

Sarı, B.; Nemli, G.; Baharoǧlu, M.; Bardak, S.; Zekoviç, E. 2012. The role of solid content of adhesive and panel density on the dimensional stability and mechanical properties of particleboard. J Compos Mater 47(10): 1247–1255. https://doi.org/10.1177/0021998312446503

Shupin, L.; Gao, L.; Wenjing, G. 2020. Effect of expanded polystyrene content and press temperature on the properties of low-density wood particleboard Maderas- Cienc Tecnol 22(4): 549-558. http://dx.doi.org/10.4067/S0718-221X2020005000413

Solt, P.; Konnerth, J.; Gindl-Altmutter, W.; Kantner, W.; Moser, J.; Mitter, R.; Van Herwijnen, H.W.G. 2019. Technological performance of formaldehyde-free adhesive alternatives for particleboard industry. Int J Adhes Adhes 94: 99-131. https://doi.org/10.1016/j.ijadhadh.2019.04.007

Thoemen, H.; Humphrey, P.E. 2003. Modeling the continuous pressing process for wood-based composites. Wood Fiber Sci 35(3): 456-468. https://wfs.swst.org/index.php/wfs/article/view/827

Turkish Standard. 1999. Wood based panels density specifications. TS EN 323.1999. TSE. Ankara, Turkey.

Turkish Standard. 1999. Wood- Based panels- Determination of dimensions of boards- Part 1: Determination of thickness, width and length. TS EN 324-1, 1999. TSE. Ankara, Turkey.

Turkish Standard. 1999. Wood-based panels- Determination of moisture content. TS EN 322. 1999. TSE. Ankara, Turkey.

Turkish Standard. 1999. Particleboards and fibreboards- Determination of swelling in thickness after immersion in water. TS EN 317. 1999. TSE. Ankara, Turkey.

Turkish Standard. 1999. Wood- Based panels- Determination of modulus of elasticity in bending and of bending strength. TS EN 310. 1999. TSE. Ankara, Turkey.

Turkish Standard. 1999. Particleboards and fibreboards- determination of tensile strength perpendicular to the plane of the board. TS EN 319. 1999. TSE. Ankara, Turkey.

Turkish Standard. 2005. Wood-based panels - Surface soundness- Test method. TS EN 311. 2005. TSE. Ankara, Turkey.

Turkish Standard. 1999. Wood based panels- Determination of formaldehyde content- Extraction method called the perforator method. TS 4894 EN 120. 1999. TSE. Ankara, Turkey.

Yel, H.; Cavdar, A.D.; Torun, S.B. 2020. Effect of press temperature on some properties of cement bonded particleboard. Maderas-Cienc Tecnol 22(1): 83-92. http://dx.doi.org/10.4067/S0718-221X2020005000108

Zhu, L.; Wang, Z.; Shao, X.; Liu, Y. 2018. Prescribed performance control for MDF continuous hot pressing hydraulic system. Int J Model Identif Control 29(3): 185. https://doi.org/10.1504/IJMIC.2018.091241

Downloads

Published

2022-11-11

How to Cite

Camlibel, O. . (2022). Influence of the multiday and continuous hot press on the physical, mechanical and formaldehyde emission properties of the particleboard. Maderas-Cienc Tecnol, 25. Retrieved from https://revistas.ubiobio.cl/index.php/MCT/article/view/5704

Issue

Section

Article