Load-carrying capacity of housings in solid timber beams
DOI:
https://doi.org/10.22320/s0718221x/2025.41Keywords:
Carpentry joints, moisture content, Pseudotsuga menziesii, self-tapping screws, timber framingAbstract
Timber framing has traditionally relied on metal fasteners, with have a high carbon footprint and often limited aesthetic appeal. These challenges can be addressed by using traditional joints such as timber housings. However, there are no design guidelines available that account for the joint geometric parameters, mechanical reinforcements, or the wood moisture content during fabrication and when loaded. In this research, the influence of joint geometry, wood moisture and reinforcement on the load-carrying capacity of solid timber beams with housings was investigated. A total of 150 Pseudotsuga menziesii (Douglas fir) beams were tested according standard, considering different moisture condition (wet or dry) at the time of cutting and at the time of testing. The tests confirmed that greater bearing depth and the use of self-tapping screws as reinforcement lead to increased load-carrying capacity. However, moisture condition significant affected only the double housings, not the single housings. In addition, 198 small-scale specimens were tested for shear, tension and compression to evaluate the impact of small clear specimen material strength on the beam load-carrying capacity. The results showed that these properties were weak predictors of housing performance. Finally, a design approach based on existing Canadian code provisions is suggested.
Downloads
References
Angst, V.; Malo, K.A. 2012. Effect of self-tapping screws on moisture induced stresses in glulam. Engineering Structures 45: 299-306. https://doi.org/10.1016/j.engstruct.2012.06.048 DOI: https://doi.org/10.1016/j.engstruct.2012.06.048
American Society for Testing and Materials. 2021. Standard Test Methods for Small Clear Specimens of Timber. ASTM D143. ASTM International: West Conshohocken, USA. https://www.astm.org
American Wood Council. 2018. National Design Specification for Wood Construction. NDS. Leesburg, VA, USA. https://awc.org/publications/2024-nds/
Canadian Standards Association. 2019. Engineering Design in Wood. CSA-O86. CSA Group: Mississauga, Canada. https://www.csagroup.org/
Claus, T.; Seim, W. 2018. Development of the multiple tenon timber connection based on experimental studies and FE simulation. Engineering Structures 173: 331-339. https://doi.org/10.1016/j.engstruct.2018.06.102 DOI: https://doi.org/10.1016/j.engstruct.2018.06.102
Danzer, M.; Dietsch, P.; Winter, S. 2016. Reinforcement of round holes in glulam beams arranged eccentrically or in groups. In: Proceedings of the World Conference on Timber Engineering. Vienna, Austria.
Dietsch, P.; Brandner, R. 2015. Self-tapping screws and threaded rods as reinforcement for structural timber elements - A state-of-the-art report. Construction and Building Materials 101: 78-89. https://doi.org/10.1016/j.conbuildmat.2015.04.028 DOI: https://doi.org/10.1016/j.conbuildmat.2015.04.028
Dietsch, P. 2017. Effect of reinforcement on shrinkage stresses in timber members. Construction and Building Materials 150: 903-915. https://doi.org/10.1016/j.conbuildmat.2017.06.033 DOI: https://doi.org/10.1016/j.conbuildmat.2017.06.033
Deutsches Institut für Bautechnik. 2019. ETA 11/0284: Heco screws. European Organisation for Technical Assessment (EOTA) DIBt: Berlin, Germany. https://www.dibt.de/en/
Fang, D.; Mueller, C. 2023. Mortise-and-tenon joinery for modern timber construction: Quantifying the embodied carbon of an alternative structural connection. Architecture, Structures and Construction 3: 11-24. https://doi.org/10.1007/s44150-021-00018-5 DOI: https://doi.org/10.1007/s44150-021-00018-5
Hanna, D.; Tannert, T. 2021. Glulam connections assembled with a combination of screws. Maderas: Ciencia y Tecnología 62(3): 1-23. http://dx.doi.org/10.4067/s0718-221x2021000100454 DOI: https://doi.org/10.4067/S0718-221X2021000100454
Hossain, A.; Popovski, M.; Tannert, T. 2018. Cross-laminated timber connections assembled with a combination of screws in withdrawal and screws in shear. Engineering Structures 168: 1-11. https://doi.org/10.1016/j.engstruct.2018.04.052 DOI: https://doi.org/10.1016/j.engstruct.2018.04.052
Hossain, A.; Popovski, M.; Tannert, T. 2019. Group Effects for Shear Connections with Self-Tapping Screws in CLT. ASCE Journal of Structural Engineering 145(8). e04019068. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002357 DOI: https://doi.org/10.1061/(ASCE)ST.1943-541X.0002357
International Organization for Standardization. 1983. Timber structures - Joints made with mechanical fasteners - General principles for the determination of strength and deformation characteristics. ISO 6891. ISO: Geneva, Switzerland. https://www.iso.org/home.html
Jockwer, R.; Steiger, R.; Frangi, A. 2014. Design model for inclined screws under varying load to grain angles. In: Proceedings of the International Network on Timber Engineering Research. Bath, United Kingdom.
Montgomery, D.C.; Runger, G.C. 2003. Applied statistics and probability for engineers. 3rd edition. Wiley: New York, USA. ISBN 978-0-471-49826-4.
Nehil, T.E.; Trojniak, B.I. 2013. Capacity of Load-Bearing Housings: Preliminary Results from Load Testing. MSc Thesis. Timber Frame Engineering Council. 195 p. https://www.tfguild.org/timber-frame-engineering
Sjödin, J.; Johansson, C. 2007. Influence of initial moisture induced stresses in multiple steel-to-timber dowel joints. Holz Roh Werk 65: 71-77. https://link.springer.com/article/10.1007/s00107-006-0136-6 DOI: https://doi.org/10.1007/s00107-006-0136-6
Sobon, J.A. 2014. Historic American Timber Joinery: A Graphic Guide. Timber Framers Guild. ISBN (no ISBN provided). https://www.tfguild.org/store/historic-american-timber-joinery
Song, X.; Zhang, Y.; Lu, Y.; Peng, Y.; Zhou, H. 2023. Experimental study on fire resistance of traditional timber mortise-tenon joints with damages. Fire Safety Journal 138. e103780. https://doi.org/10.1016/j.firesaf.2023.103780 DOI: https://doi.org/10.1016/j.firesaf.2023.103780
Tannert, T. 2016. Improved performance of reinforced rounded dovetail joints. Construction and Building Materials 118: 262-267. https://doi.org/10.1016/j.conbuildmat.2016.05.038 DOI: https://doi.org/10.1016/j.conbuildmat.2016.05.038
Tannert, T.; Lam, F. 2009. Timber Construction Self-tapping Screws as Reinforcement for Rounded Dovetail Connections. Structural Control & Health Monitoring 16(3): 374-384. https://doi.org/10.1002/stc.283 DOI: https://doi.org/10.1002/stc.283
Tannert, T.; Vallée, T.; Hehl, S. 2012. Experimental and numerical investigations on adhesively bonded hardwood joints. International Journal of Adhesion and Adhesives 37: 65-69. https://doi.org/10.1016/j.ijadhadh.2012.01.014 DOI: https://doi.org/10.1016/j.ijadhadh.2012.01.014
United States Department of Agriculture. 2010. Wood Handbook, Forest Products Laboratory. Madison, Wisconsin, USA. https://research.fs.usda.gov/treesearch/62200
Xie, Q.; Wang, L.; Zheng, P.; Zhang, L.; Hu, W. 2017. Rotational behavior of degraded traditional mortise-tenon joints: experimental tests and hysteretic model. International Journal of Architectural Heritage 12(1): 125-136. https://doi.org/10.1080/15583058.2017.1390629 DOI: https://doi.org/10.1080/15583058.2017.1390629
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
Los autores/as conservarán sus derechos de autor y garantizarán a la revista el derecho de primera publicación de su obra, el cuál estará simultáneamente sujeto a la Licencia de Reconocimiento de Creative Commons CC-BY que permite a terceros compartir la obra siempre que se indique su autor y su primera publicación esta revista.
