Impact of nano-aluminum-oxide impregnation, densification, and vapor pre-treatment on the physical and mechanical properties of white willow wood
DOI:
https://doi.org/10.22320/s0718221x/2026.16Keywords:
Aluminum oxide nanoparticles, fast-growing wood species, physical and mechanical properties, white willow, wood impregnationAbstract
Fast-growing wood species are often characterized by low density, unsatisfactory mechanical properties, and poor biological durability. Therefore, various modification techniques have been tested to improve these disadvantages. The aim of this research work was to investigate the effects of densification of Salix alba (white willow) under hot pressing for 15 and 30 minutes on its physical and mechanical properties. Vapor pre-treatment for four and six hours was also applied to mitigate the negative effects of cracks and checks caused by breakage in wood cell wall under pressure. Markedly, separate sets of specimens were impregnated with aluminum oxide nano-suspension to evaluate if an increase in thermal conductivity would improve the properties of wood. The results indicated that densification significantly enhanced both the physical and mechanical properties of the wood. The four-hour vapor pre-treatment demonstrated the optimal improving results in both hot pressing durations. Though impregnation of specimens with the nano-suspension improved some properties (including spring back, hardness, and physical properties), most of the studied mechanical properties did not show any statistically significant improvement. Therefore, it was concluded that densifying willow wood for 15 minutes with a four-hour vapor pre-treatment yields optimal results. The enhancement in mechanical properties due to nano-aluminum oxide was not substantial enough to justify the associated costs, and thus, its use is not recommended for industrial applications.
Downloads
References
Ali, M.R.; Abdullah, U.H.; Ashaari, Z.; Hamid, N.H.; Hua, L.S. 2022. Hydrothermalmodification of wood: A review. Polymers 13. e2612. https://doi.org/10.3390/polym13162612 DOI: https://doi.org/10.3390/polym13162612
Anshari, B.; Guan, Z.W.; Kitamori, A.; Jung, K.; Komatsu, K. 2012. Structuralbehaviour of gluedlaminatedtimberbeamspre-stressedbycompressedwood. Construction and BuildingMaterials 29: 24-32. https://doi.org/10.1016/j.conbuildmat.2011.10.002 DOI: https://doi.org/10.1016/j.conbuildmat.2011.10.002
Argaman, N.; Makov, G. 2000. Densityfunctionaltheory: Anintroduction. American Journal of Physics 68: 69-79. https://doi.org/10.1119/1.19375 DOI: https://doi.org/10.1119/1.19375
ASTM .2023. D143-22. Standard Test Methods for Small Clear Specimens of Timber. American Society for Testing and Materials, West Conshohocken.
Barbu, M.C.; Buresova, K.; Tudor, E.M.; Petutschnigg, A. 2022. Physical and mechanicalproperties of Paulownia tomentosa × elongatasawnwoodfromSpanish, Bulgarian and Serbianplantations. Forests 13. e1543. https://doi.org/10.3390/f13101543 DOI: https://doi.org/10.3390/f13101543
Bektas, I.; Tutuş, A.; Gültekin, G. 2020. The effect of sapwood and heartwooddifferencesonmechanicalproperties of fast-growingtreespecies. DrvnaIndustrija 71(3): 261-269. https://doi.org/10.5552/drvind.2020.1940 DOI: https://doi.org/10.5552/drvind.2020.1940
Bergman, T.; Lavine, A.; Incropera, F.; DeWitt, D. 2011. Fundamentals of heat and mass transfer. 7th edition. John Wiley &Sons: New York, USA.
Bi, W.; Li, H.; Hui, D.; Gaff, M.; Lorenzo, R.; Corbi, I.; Corbi, O.; Ashraf, M. 2021. Effects of chemicalmodification and nanotechnologyonwoodproperties. NanotechnologyReviews 10: 978-1008. https://doi.org/10.1515/ntrev-2021-0065 DOI: https://doi.org/10.1515/ntrev-2021-0065
Čabalová, I.; Výbohová, E.; Igaz, R.; Kristak, L.; Kačík, F.; Antov, P.; Papadopoulos, A.N. 2022. Effect of oxidizingthermalmodificationonthechemicalproperties and thermalconductivity of Norwayspruce (Picea abies L.) wood. Wood Material Science&Engineering 17(5): 366-375. https://doi.org/10.1080/17480272.2021.2014566 DOI: https://doi.org/10.1080/17480272.2021.2014566
Cabral, J.P.; Kafle, B.; Subhani, M.; Reiner, J.; Ashraf, M. 2022. Densification of timber: A reviewontheprocess, material properties, and application. Journal of Wood Science 68. e20. https://doi.org/10.1186/s10086-022-02028-3 DOI: https://doi.org/10.1186/s10086-022-02028-3
Çavuş, V.; Şahin, S.; Esteves, B.; Ayata, U. 2019. Determination of thermalconductivityproperties in somewoodspeciesobtainedfromTurkey. BioResources 14(3): 6709-6715. https://doi.org/10.15376/biores.14.3.6709-6715 DOI: https://doi.org/10.15376/biores.14.3.6709-6715
David, D. 2022. Whatiswillowwood? A comprehensiveguide. https://woodworkingclarity.com/what-is-willow-wood/
Feng, C.H.; Mariotti, H.; Cloutier, A.; Koubaa, A.; Blanchet, A. 2012. Densification of woodveneersbycompressioncombinedwithheat and steam. European Journal of Wood and Wood Products 70: 155-163. https://doi.org/10.1007/s00107-011-0524-4 DOI: https://doi.org/10.1007/s00107-011-0524-4
Gaitán-Alvarez, J.; Moya, R.; Mantanis, G.I.; Berrocal, A. 2021. Furfurylation of tropical wood species with and withoutsilvernanoparticles: Part I. Wood Material Science&Engineering 17(6): 410-419. https://doi.org/10.1080/17480272.2021.1886166 DOI: https://doi.org/10.1080/17480272.2021.1886166
Gérardin, P. 2016. New alternativesforwoodpreservationbasedonthermal and chemicalmodification of wood- a review. Annals of Forest Science 73(3): 559-570. https://doi.org/10.1007/s13595-015-0531-4 DOI: https://doi.org/10.1007/s13595-015-0531-4
Goli, G.; Cremonini, C.; Negro, F.; Zanuttini, R.; Fioravanti, M. 2014. Physical-mechanicalproperties and bondingquality of heattreatedpoplar and ceiba plywood. iForest 8(5): 687-692. https://doi.org/10.3832/ifor1276-007 DOI: https://doi.org/10.3832/ifor1276-007
Grimme, S. 2006. Semiempirical GGA-typedensityfunctionalconstructedwith a long-rangedispersioncorrection. Journal of ComputationalChemistry 27(15): 1787-1799. https://doi.org/10.1002/jcc.20495 DOI: https://doi.org/10.1002/jcc.20495
Gryc, V.; Giagli, K.; Fajstavr, M.; Vavrcík, H. 2017. Willows in Czechlowlands: Variability of density and shrinkage. In: Proceedings of the 8th International ConferenceonInformation and Communication Technologies in Agriculture, Food&Environment. Chania, Greece, 21-24 September 2017, pp. 554-560.
Istikowati, W.; Ishiguri, F.; Aiso, H.; Hidayati, F.; Tanabe, J.; Iizuka, K.; Sutiya, B.; Wahyudi, I.; Yokota, S. 2014. Physical and mechanical properties of woods from three native fast-growing species in a secondary forest in South Kalimantan, Indonesia. Forest Products Journal 64(1-2): 48-54. https://doi.org/10.13073/FPJ-D-13-00069 DOI: https://doi.org/10.13073/FPJ-D-13-00069
Jiang, J.; Du, J.; Li, H.; Mei, C.; Gong, X. 2022. Hydrophobicityimprovementonwoodfor a betterapplication of this bio-based material. Coatings 12(10). e1465. https://doi.org/10.3390/coatings12101465 DOI: https://doi.org/10.3390/coatings12101465
Kaith, B.S.; Mittal, H.; Jindal, R.; Maiti, M.; Kalia, S. 2011. Environmentbenevolent biodegradable polymers: synthesis, biodegradability, and applications. In: Cellulose fibers: bio- and nano-polymer composites. Springer: Berlin, Germany, pp. 425-451. https://doi.org/10.1007/978-3-642-17370-7_16 DOI: https://doi.org/10.1007/978-3-642-17370-7_16
Karp, A. 2014. Willows as a source of renewablefuels and diverse products. In: Challenges and opportunitiesfortheworld'sforests in the 21st century. Springer: Dordrecht, Netherlands, pp. 617-641. https://doi.org/10.1007/978-94-007-7076-8_27 DOI: https://doi.org/10.1007/978-94-007-7076-8_27
Kozakiewicz, P.; Laskowska, A.; Drozdzek, M.; Zawadzki, J. 2022. Influence of thermalmodification in nitrogenatmosphereonphysical and technologicalproperties of Europeanwoodspecies. Coatings 12(11). e1663. https://doi.org/10.3390/coatings12111663 DOI: https://doi.org/10.3390/coatings12111663
Kutnar, A.; Sernek, M. 2007. Densification of wood. Zbornik Gozdarstva in Lesarstva 82: 53-62.
Ledin, S. 1996. Willowwoodproperties, production and economy. Biomass and Bioenergy 11(2-3): 75-83. https://doi.org/10.1016/0961-9534(96)00022-0 DOI: https://doi.org/10.1016/0961-9534(96)00022-0
Lee, S.H.; Lum, W.C.; Zaidon, A.; Maminski, M. 2015. Microstructural, mechanical and physicalproperties of post heat-treatedmelamine-fortifiedparticleboard. European Journal of Wood and Wood Products 73: 607-616. https://doi.org/10.1007/s00107-015-0924-y DOI: https://doi.org/10.1007/s00107-015-0924-y
Luan, Y.; Fang, C.H.; Ma, Y.F.; Fei, B.H. 2022. Wood mechanicaldensification: A reviewonprocessing. Materials and ManufacturingProcesses 37(4): 359-371.https://doi.org/10.1080/10426914.2021.2016816 DOI: https://doi.org/10.1080/10426914.2021.2016816
Lykidis, C.; Bak, M.; Mantanis, G.; Németh, R. 2016. Biologicalresistance of pinewoodtreatedwith nano-sized zinc oxide and zinc borate. European Journal of Wood and Wood Products 74: 909-911. https://doi.org/10.1007/s00107-016-1093-3 DOI: https://doi.org/10.1007/s00107-016-1093-3
Mantanis, G.I. 2017. Chemical modification of woodbyacetylationorfurfurylation. BioResources 12(2): 4478-4489. https://doi.org/10.15376/biores.12.2.mantanis DOI: https://doi.org/10.15376/biores.12.2.Mantanis
Militz, H. 2020. Wood modificationresearch in Europe. Holzforschung 74(4). e333. https://doi.org/10.1515/hf-2020-0050 DOI: https://doi.org/10.1515/hf-2020-0050
Moya, R.; Muñoz, F. 2010. Physical and mechanicalproperties of eightfast-growingplantationspecies in Costa Rica. Journal of Tropical Forest Science 22(3): 317-328. https://www.jstor.org/stable/23616661
Nishiyama, Y.; Langan, P.; Chanzy, H. 2002. Crystalstructure and hydrogen-bondingsystem in cellulose Iβ. Journal of the American Chemical Society 124. e9074. https://doi.org/10.1021/ja0257319 DOI: https://doi.org/10.1021/ja0257319
Oliva, R.; Salvini, A.; Di Giulio, G.; Capozzoli, L.; Fioravanti, M.; Giordano, C.; Perito, B. 2015. TiO₂-oligoaldaramidenanocomposites as efficientcore–shellsystemsforwoodpreservation. Journal of Applied PolymerScience 132. e42047. https://doi.org/10.1002/app.42047 DOI: https://doi.org/10.1002/app.42047
Ozaki, T.; Kino, H.; Yu, J.; Han, M.J. 2018. User’s manual of OpenMXversion 3.8. http://www.openmx-square.org/openmx_man3.8/openmx.html
Papadopoulos, A.N.; Bikiaris, D.N.; Mitropoulos, A.C.; Kyzas, G.Z. 2019. Nanomaterials and chemicalmodificationsforenhancedkeywoodproperties. Nanomaterials 9(4). e607. https://doi.org/10.3390/nano9040607 DOI: https://doi.org/10.3390/nano9040607
Pásztory, Z.; Fehér, S.; Börcsök, Z. 2020. The effect of heattreatmentonthermalconductivity of paulowniawood. European Journal of Wood and Wood Products 78: 205-207. https://doi.org/10.1007/s00107-019-01470-3 DOI: https://doi.org/10.1007/s00107-019-01470-3
Perdew, J.P.; Burke, K.; Ernzerhof, M. 1996. Generalizedgradientapproximationmade simple. PhysicalReviewLetters 77.e3865. https://doi.org/10.1103/PhysRevLett.77.3865 DOI: https://doi.org/10.1103/PhysRevLett.77.3865
Rassam, G.; Ghofrani, M.; Taghiyari, H.R.; Jamnani, B.; Khajeh, M.A. 2012. Mechanical performance and dimensional stability of nano-silverimpregnateddensifiedsprucewood. European Journal of Wood and Wood Products 70: 595-600. https://doi.org/10.1007/s00107-011-0590-7 DOI: https://doi.org/10.1007/s00107-011-0590-7
Sadatnezhad, S.H.; Khazaeian, A.; Sandberg, D.; Tabarsa, T. 2017. Continuoussurfacedensification of wood. BioResources 12(2): 3122-3132. https://doi.org/10.15376/biores.12.2.3122-3132 DOI: https://doi.org/10.15376/biores.12.2.3122-3132
Sandberg, D.; Haller, P.; Navi, P. 2013. Thermo-hydro and thermo-hydro-mechanicalwoodprocessing. Wood Material Science&Engineering 8(1): 64-68. https://doi.org/10.1080/17480272.2012.751935 DOI: https://doi.org/10.1080/17480272.2012.751935
Sandberg, D.; Kutnar, A. 2016. Thermalmodifiedtimber. Wood and FiberScience 48(1): 28-39.https://www.diva-portal.org/smash/get/diva2:1013948/FULLTEXT01.pdf
Sandberg, D.; Kutnar, A.; Mantanis, G. 2017. Wood modificationtechnologies – a review. iForest 10(6): 895-908. https://doi.org/10.3832/ifor2380-010 DOI: https://doi.org/10.3832/ifor2380-010
Scharf, A.; Neyses, B.; Sandberg, D. 2023. Continuousdensification of woodwith a beltpress. Wood Material Science&Engineering 18(4): 1573-1586. https://doi.org/10.1080/17480272.2023.2228278 DOI: https://doi.org/10.1080/17480272.2023.2216660
Sotayo, A.; Bradley, D.; Bather, M.; Sareh, P.; Oudjene, M.; El-Houjeyri, I.; Harte, A.; Mehra, S.; O’Ceallaigh, C.; Haller, P.; Namari, S.; Makradi, A.; Belouettar, S.; Bouhala, L.; Deneufbourg, F.; Guan, Z. 2020. Review of state of the art of dowellaminatedtimbermembers. Developments in theBuiltEnvironment 1. e100004. https://doi.org/10.1016/j.dibe.2019.100004 DOI: https://doi.org/10.1016/j.dibe.2019.100004
Taghiyari, H.R.; Norton, J.; Tajvidi, M. 2016. Effects of nano-materialsondifferentproperties of wood-composite materials. In: Bio-based Wood adhesives. CRC Press: Boca Raton, USA. DOI: https://doi.org/10.1201/9781315369242-14
Taghiyari, H.R.; Rassam, G.; Ahmadi-DavazdahEmam, K. 2017. Effects of densificationonuntreated and nano-aluminum-oxide impregnatedpoplarwood. Journal of ForestryResearch 28: 403-410. https://doi.org/10.1007/s11676-016-0321-3 DOI: https://doi.org/10.1007/s11676-016-0321-3
Taghiyari, H.R.; Tajvidi, M.; Taghiyari, R.; Mantanis, G.I.; Esmailpour, A.; Hosseinpourpia, R. 2020a. Nanotechnology for wood qualityimprovement and protection. In: Nanomaterialsforagriculture and forestryapplication. Elsevier: Amsterdam, Netherlands, pp. 469-489. https://doi.org/10.1016/B978-0-12-817852-2.00019-6 DOI: https://doi.org/10.1016/B978-0-12-817852-2.00019-6
Taghiyari, H.R.; Esmailpour, A.; Majidi, R.; Morrell, J.J.; Mallaki, M.; Militz, H.; Papadopoulos, A.N. 2020b. Potential use of wollastonite as a filler in UF resinbased MDF. Polymers 12. e1435. https://doi.org/10.3390/polym12071435 DOI: https://doi.org/10.3390/polym12071435
Thomas, A.; Priault, P.; Piutti, S.; Dallé, E.; Marron, N. 2021. Growthdynamics of fast-growingtreespecies. Forest Ecology and Management 480. e118672. https://doi.org/10.1016/j.foreco.2020.118672 DOI: https://doi.org/10.1016/j.foreco.2020.118672
Welzbacher, C.R.; Wehsener, J.; Rapp, A.O.; Haller, P. 2008. Thermo-mechanical densification combined with thermal modification of Norway spruce. European Journal of Wood and Wood Products 66: 39-49. https://doi.org/10.1007/s00107-007-0198-0 DOI: https://doi.org/10.1007/s00107-007-0198-0
Xu, B.H.; Wang, B.L.; Yu, K.B.; Bouchair, A. 2021. Anoptionalconnection material in timberstructures. Journal of MaterialsScience 56(6): 14114-14125. https://doi.org/10.1007/s10853-021-06194-5 DOI: https://doi.org/10.1007/s10853-021-06194-5
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
Los autores/as conservarán sus derechos de autor y garantizarán a la revista el derecho de primera publicación de su obra, el cuál estará simultáneamente sujeto a la Licencia de Reconocimiento de Creative Commons CC-BY que permite a terceros compartir la obra siempre que se indique su autor y su primera publicación esta revista.
